Discovering Plumbing Basics is Important For Installing a Bathtub
Discovering Plumbing Basics is Important For Installing a Bathtub
Blog Article
On this page below you can get additional very good facts with regards to Tools You Need to Install a New Bathtub .
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is conveniently accessible, the project can relocate speedily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and set in the new one. Ensure you have qualified yourself for the work and also are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and also do not need to change the arrangement of your previous water pipes.
Your tools and material checklist ought to make up the following:
Preparing for the Installment
First of all, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub until the level checks out degree.
To set up taps, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water and also check all joints and new pipework for leakages and tighten them if essential. Fill the bath tub and additionally examine the overflow outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling as well as sealing around the tub must wait up until the tub has been used at least once as this will certainly resolve it right into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washing machines are in place in between the tap as well as the sink. Secure the tap in position with the producer offered backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split rather very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about Installing A Bathtub. Thanks a ton for finding the time to read through our content. Sharing is caring. Helping people is fun. Thank you for taking the time to read it.
Stress-free fix? Contact. Report this page